Close-up of the bike
Detail pictures of it clean can be seen at this prior post.
It took me a while to get there, well, like it always does. It's 3 hours if I'm really hittin' on all sixes. I've done it in 2:50, but I'm just not in that kind of fitness right now.
Also, I decided to set the Hunter up with thumbies, for the sake of total simplicity and reliability. But that kind of means 8-speed. I know, it can be done with 9-speed if you don't mind friction, which I don't. But I also like the durability of 8-speed.
Why does that have anything to do with how long it took me to get up there?
Gosh, it's kind of embarrassing...
I was between the gearing that I normally have going when I climb that. With 9-speed I get a 12-34 cluster (well, maybe 11-34, but that's not important). With the 34 I have mid-ring 1st gear 32:34, 2nd gear 32:30, 3rd gear 32:26. With a 12-32 block, it's 32:32, 32:28, 32:24.
I usually climb the first half in 3rd, 32:26 then slip to 2nd when the air gets thinner and my legs get tired. Well, 32:24 was too high and I couldn't really stay on top of it. But 32:28 was too low. Until I got tired and it was too high. I know, whining is unacceptable.
But I do know that with a load, 22:32 is going to be a not low enough granny. I wanted to use 20-30-42 chainrings on this bike, but I also wanted a Shimano crank with external bearings. I see Mr Whirly crankarms in my future.
I was really hoping to discover that the snow melt had happened enough that I could ride down the Silver Creek Trail. I headed south on the CDT to check it out.
Nope.
Those drifts were not soft. They were hard. I hit that section of trail at about 10 AM, and those suckers were hard as rock. Not much melt probably happened today. It just hasn't been getting very warm.
I went down the Poncha Creek road. Haven't done that kind of rock gauntlet on a fully rigid bike in many years. Ouch. How do you do that Ed? Pinch flatted, which was a good excuse to let my wrists and hands recover.
It's almost summer. Time for high country riding, snow or no.
Also, I decided to set the Hunter up with thumbies, for the sake of total simplicity and reliability. But that kind of means 8-speed. I know, it can be done with 9-speed if you don't mind friction, which I don't. But I also like the durability of 8-speed.
Why does that have anything to do with how long it took me to get up there?
Gosh, it's kind of embarrassing...
I was between the gearing that I normally have going when I climb that. With 9-speed I get a 12-34 cluster (well, maybe 11-34, but that's not important). With the 34 I have mid-ring 1st gear 32:34, 2nd gear 32:30, 3rd gear 32:26. With a 12-32 block, it's 32:32, 32:28, 32:24.
I usually climb the first half in 3rd, 32:26 then slip to 2nd when the air gets thinner and my legs get tired. Well, 32:24 was too high and I couldn't really stay on top of it. But 32:28 was too low. Until I got tired and it was too high. I know, whining is unacceptable.
But I do know that with a load, 22:32 is going to be a not low enough granny. I wanted to use 20-30-42 chainrings on this bike, but I also wanted a Shimano crank with external bearings. I see Mr Whirly crankarms in my future.
I was really hoping to discover that the snow melt had happened enough that I could ride down the Silver Creek Trail. I headed south on the CDT to check it out.
Nope.
Those drifts were not soft. They were hard. I hit that section of trail at about 10 AM, and those suckers were hard as rock. Not much melt probably happened today. It just hasn't been getting very warm.
I went down the Poncha Creek road. Haven't done that kind of rock gauntlet on a fully rigid bike in many years. Ouch. How do you do that Ed? Pinch flatted, which was a good excuse to let my wrists and hands recover.
It's almost summer. Time for high country riding, snow or no.
2 comments:
Nice bike Tom! You know if you rode the single speed more your legs would probably be happy with any gearing you had, whether 8 speed or even two speed. :-)
Tom, I have no freakin' idea how I do it.
Nice bike!!
Ed
Post a Comment